7.3 Powerstroke Glow Plugs: Overview and Replacement Notes
- Written by
- Diesel Glow Plug Editorial Team
- Reviewer
- Diesel Glow Plug Editorial Team
- Review date
- First published
Ford's owner supplement for the 7.3L Power Stroke says the engine's glow plug system consists of eight glow plugs, a glow plug relay, an oil temperature sensor and a barometric pressure sensor, controlled by the powertrain control module. This page summarizes what Ford says, how testing and replacement fit in, and why part numbers must come from Ford or the plug maker's catalog.
This is part of: Diesel Glow Plugs: What They Do, Failure Signs and Replacement
This page covers the 7.3 Powerstroke glow plugs as Ford describes them. It sits under the glow plug guide. Ford, Powerstroke and 7.3L are used here only to name the engine; this site is not affiliated with the maker, sells nothing and offers no repair service.
Short answer: what the engine uses and where to check fitment
Ford’s 2000 owner supplement says the 7.3L glow plug system consists of eight glow plugs, a glow plug relay, an engine oil temperature sensor and a barometric pressure sensor, all controlled electronically by the powertrain control module. Part numbers and fitment are not given on this page. Confirm them in Ford’s documentation for your exact vehicle and year, or in the plug maker’s catalog, and never match a part by guesswork.
How the system works on this engine
Per Ford’s supplement, the module energizes the plugs immediately after the ignition is turned ON and then sets the on-time from oil temperature and barometric pressure, with the time decreasing as both rise. The WAIT TO START light stays on while heat is needed.
- Wait until the light goes off, then start.
- Do not crank for more than 30 seconds at a time; if the engine does not start, turn the key off and wait 30 seconds.
- After the engine starts, Ford says the plugs stay activated for up to two minutes. If the engine is not started before activation ceases, reset by turning the key to OFF.
- Do not use starting fluid such as ether. Ford warns it can cause immediate explosive damage and possible personal injury.
See what a glow plug does for the general sequence.
Symptoms and testing for this engine
Ford’s guidance is simple: if the WAIT TO START light does not light briefly with a cold engine and the key ON, the glow plug system should be checked and repaired promptly. Ford’s diagnostic summary for the California-calibrated system shows the module can flag individual plug circuits, with codes P0671 to P0678 for circuits 1 to 8; it also says glow plug diagnostics do not set the check-engine light on Federal trucks over 8,500 lb.
For how to test, read how to test glow plugs first. Ford’s documents we opened give no owner resistance value or test procedure, so this site gives none; use Ford’s service manual for your truck. The glow plug resistance check helper compares a reading to a range you supply.
Plug and relay system
The relay is one part of the circuit. Ford’s diagnostic summary describes the California-calibrated system as built around a solid-state glow plug control module, while the owner supplement lists a relay, so confirm which your truck has before identifying parts. See the 7.3 Powerstroke glow plug relay page for the relay’s function and the checks that come before replacing it.
Replacement overview and safety
Replacement is a technician’s job if plugs are seized, access is awkward or you cannot support the truck safely. Bosch recommends replacing all plugs together and warns that a seized plug can break off in the head, which would require time-consuming cylinder head disassembly.
Safety
engine off and cool; follow your service manual for battery handling; no open flame or sparks near fuel; never work under the truck on a jack alone. A Ford dealer bulletin hosted by NHTSA (written for an unrelated F-150 Lightning recall, but carrying Ford’s standard jacking warnings) says never to get under a vehicle supported only by a jack, to support it with floor stands, to raise it only on a hard, level surface and to block the wheels that stay on the ground. Stop and see a qualified technician for a seized or broken plug, a fuel leak or a flashing warning light with other messages.
Part-number rule
This page lists no part numbers. Confirm the plug and relay for your truck in the maker’s catalog or manual, using the model year and emissions package, and replace the full set together per Bosch. For what affects the bill, see what drives the price of a plug job.
Answers to common questions
How many glow plugs does a 7.3 have?
Ford's 2000 supplement for the 7.3L Power Stroke says the glow plug system includes eight glow plugs. Ford's diagnostic summary for the engine also lists fault codes for glow plug circuits 1 through 8. Confirm for your vehicle in the Ford documentation for your model year, since this page reflects only the Ford documents opened for it.
Does the 7.3 need the relay replaced too?
Ford's documents we reviewed do not say that a relay should be replaced with the plugs. They list the relay as one part of the system and do not give a rule. Whether to replace it depends on testing and your service manual. The relay page covers its function and what Ford says about the circuit.
What are common failure causes?
Ford's documents give no failure-cause list for this engine. Bosch, a plug maker, lists excessive voltage as the leading cause of glow plug failure, and its fault-diagnosis poster also lists causes such as premature injection and nozzles with carbon deposits. A technician with your engine's service data can tell which applies, so test before replacing parts.
Can I use starting fluid on a 7.3?
No. Ford's 7.3L supplement says not to use starting fluid such as ether in the air intake system, because it could cause immediate explosive damage to the engine and possible personal injury. If the engine will not start in the cold, work through the wait-to-start light, glow plug system and block heater instead, or see a technician.
What does the wait-to-start light do on a 7.3?
Ford says the WAIT TO START light illuminates with the key ON if glow plug heat is needed, and you should wait until it goes off before starting. It should always light briefly when the engine is cold, and if it does not, the glow plug system should be checked and repaired promptly to avoid cold-start difficulty.
Sources
- Ford: 7.3L Power Stroke Diesel Supplement to the Owner Guide (2000)fordservicecontent.com
- Ford: 2000 MY OBD System Operation Summary for 7.3L Diesel Enginefordservicecontent.com
- Bosch Auto Parts (US): Glow Plugs, technical information and FAQboschautoparts.com
- Bosch: Glow plugs Duraterm, Duraterm HighSpeed and DuraSpeed (brochure)boschaftermarket.com
- Bosch: Fault diagnosis at a glance, glow plug faces (poster)boschaftermarket.com
Worth reading next
- Diesel Glow Plugs: What They Do, Failure Signs and Replacement
Diesel glow plugs explained: what a glow plug does, how the wait-to-start sequence works, failure signs, testing and when replacement belongs to a shop.
- 7.3 Powerstroke Glow Plug Relay: Function, Failure Signs, Testing
What the 7.3 Powerstroke glow plug relay does, how its failure can look, and the safe order for checking it before replacing glow plugs or parts.
- Glow Plug Light: What It Means and What to Do When It Flashes
What the diesel glow plug light means, how normal wait-to-start differs from a fault, and what to check or do when it flashes or stays on.
- Glow Plug Replacement Cost: What Drives the Price
What drives glow plug replacement cost: plug count, engine access, seized plugs and labor. Learn how to get a quote, with no price claims here.
- How to Test Glow Plugs: Safe Methods and Readings
How to test glow plugs safely: the safety rules, what a resistance check can tell you, other causes to rule out, and when to hand it to a technician.
- What Does a Glow Plug Do?
What does a glow plug do? It pre-heats a diesel's combustion chamber for cold starts. See the key-on to afterglow sequence and why gas engines skip it.