Go to main content
Diesel Glow Plug
Search

Glow Plug Resistance Check Helper

Written by First published

This helper compares an ohm reading with the figure your engine maker publishes. You enter the meter reading, the meter lead resistance and the maker's spec and tolerance from your manual; it shows the difference and whether the reading sits inside the band you entered. It names no universal spec and does not judge a plug or an engine.

Glow plug resistance check

Enter your meter reading and the figures from your manual. Results update as you type, the numbers are saved in the page address so you can bookmark or share them, and nothing leaves your browser. Do not start a test until you have read the safety note below.

Reading and maker spec

Leave blank only if you ticked OL.

Touch the probes together and enter that reading. Blank counts as 0.

From your manual. The starting 1 is a placeholder for the worked example, not a spec.

From your manual. Enter 0 if it gives one figure only. The starting 0.5 is a placeholder.

Your comparison

How the helper works

It subtracts the lead resistance from your reading, compares the result with your maker's spec and tolerance, and applies Ohm's law for an approximate current. Every spec is your input; the helper holds no table of ohm values.

Reading versus spec
net      = measured - lead
delta    = net - spec
delta %  = delta / spec x 100
band     = spec - tolerance  to  spec + tolerance
inside   = |delta| <= tolerance
I (amps) = V / net      [approximate, cold resistance]
measured
meter reading in ohms
lead
resistance of the meter leads with the probes touching
spec, tolerance
figures you enter from your engine maker's manual
V
system voltage, 12 or 24

Worked example

Given: 12 V system; meter reads 1.10 ohm, leads read 0.20 ohm; placeholder spec 1.00 ohm, tolerance 0.50 ohm.

  1. Net reading: 1.10 - 0.20 = 0.90 ohm
  2. Difference from spec: 0.90 - 1.00 = -0.10 ohm (-10%)
  3. Band entered: 0.50 to 1.50 ohm, and |-0.10| <= 0.50
  4. Approximate current: 12 / 0.90 = 13.33 A

Answer: The reading is inside the band the user entered. That says nothing about the plug or the engine, because the spec in this example is a placeholder.

What to take from your manual before you start
ItemWhere it comes fromWhat the helper does with it
Spec resistance Owner's manual or maker's service data, for your engine and yearCompared with the net reading
Tolerance Same documentSets the band around the spec
System voltage Your vehicle (12 V or 24 V)Used only for the approximate current
Test method Same documentNot covered here: follow it exactly

No ohm values are published here. The helper has no data file of specs.

Assumptions and limits

  • The spec, tolerance, voltage and reading are yours; the starting numbers are placeholders for the worked example.
  • The comparison is arithmetic on your numbers. It does not say that a plug is good or bad, and it cannot rule out a relay, controller, fuse, wiring or battery cause.
  • Current uses the cold resistance and ignores wiring and relay losses.
  • OL is treated as an open circuit on that reading only.

Answers to common questions

What is the resistance of a good glow plug?

There is no single value. The figure depends on the engine, the plug type and the system voltage, so the helper has no built-in spec. Look it up in your owner's manual or the maker's service data and enter it. This site does not call a plug good or bad.

What does OL on the meter mean?

OL means the meter sees a resistance above its range, which is an open circuit on that reading. It can come from the part, the connection, the leads or the way the meter is set up. Re-check the connections and your manual's method before drawing any conclusion.

Why subtract the meter lead resistance?

Low readings include the resistance of the meter leads and contacts. Touch the two probes together, note the reading, and enter it as the lead resistance. The helper subtracts it so the reading is closer to the plug alone.

Why is the current an approximation?

The helper divides the system voltage by the net cold resistance (I = V / R). Resistance changes with temperature, and the plug is wired into a relay and controller circuit, so the real current differs. It is a rough size check only.

If the reading is inside my band, are the glow plugs fine?

Not necessarily. A reading in the band you entered says only that one measurement is near the figure you typed. A relay, controller, wiring, fuse or battery problem can also stop glow plugs working, and this helper cannot rule any of them out.

Is it safe to test with the engine hot or the battery connected?

Test only as your manual describes. As a general rule the engine is off and cool, and the manual says whether to disconnect the battery. If the manual does not describe a resistance test, ask a qualified technician.

Sources

  1. Your engine's owner's manual or the maker's service data (the only source for the spec and tolerance) (dieselglowplug.com) Editorial policy: how specs are handled on this site.

Worth reading next