Go to main content
Diesel Glow Plug
Search

7.3 Powerstroke Glow Plug Relay: Function, Failure Signs, Testing

Review date
First published

On Ford's 7.3L Power Stroke, the glow plug relay is the switch in the glow plug circuit: Ford's owner supplement lists it with eight glow plugs and two sensors, all controlled by the powertrain control module. When it fails to switch, the plugs may not heat. This page explains the role and a safe order of checks, not a repair procedure.

Small automotive relay and wiring connector on a wooden workbench beside a digital multimeter

The glow plug relay on a 7.3 Powerstroke is part of the circuit that powers the plugs. This page sits under the 7.3 Powerstroke glow plugs guide and the wider glow plug guide. Ford and Powerstroke are used only to name the engine; this site sells nothing and does not repair vehicles.

Short answer

A relay is an electrically operated switch, and on this engine it sits in the glow plug system. Ford’s 2000 owner supplement for the 7.3L lists it with eight glow plugs, an engine oil temperature sensor and a barometric pressure sensor, and says the system is controlled by the powertrain control module (PCM). Part numbers, location and test values are not given here because the Ford documents opened for this page do not provide them.

What the relay does in the glow plug circuit

In Ford’s description, the PCM energizes the glow plugs immediately after the ignition is placed in the ON position, then decides how long they stay on, using oil temperature and barometric pressure. Ford lists the relay as one part of that chain. The WAIT TO START light tells you when to start; Ford says to wait until it goes off.

Some trucks differ. Ford’s diagnostic summary describes a California-calibrated system built around a solid-state glow plug control module that drives the individual plugs, with on-time normally between 1 and 120 seconds and an internal 180-second limit. That module also reports individual plug circuit faults to the PCM. Which one your truck has depends on year and emissions package, so check your documentation.

Failure signs

The signs of a relay problem look like the signs of a glow plug problem. Ford says the WAIT TO START light should always illuminate briefly with a cold engine and key ON and that, if it does not, the system should be checked and repaired promptly to avoid cold-start difficulty. Bosch lists hard starting, long cranking, rough idle after start and excess exhaust emissions after start as signs the glow plug system needs attention. None of those pins the fault on the relay.

Because the light is driven by the control system, a lit light does not prove the plugs are heating. The Ford documents opened do not say it does.

Testing safely

Test in this order, and stop at any point where the manual says to hand off to a technician.

  1. Read the Ford documentation for your truck’s year and emissions package, so you know whether it has a relay or a control module.
  2. Check the simple things first: battery condition and connections as the manual describes, and the behavior of the light described in the glow plug light guide.
  3. Do any meter work only with the procedure and values from the Ford service manual. This page gives no meter steps or values, because none were available in the sources opened.
  4. Test the plugs themselves using how to test glow plugs, so you do not replace a relay when plugs are the fault, or the reverse.

Safety

handle the battery only as the manual says; engine off and cool; no sparks or open flame near fuel; never work under the truck on a jack alone. A Ford dealer bulletin hosted by NHTSA (written for an unrelated F-150 Lightning recall, but carrying Ford’s standard jacking warnings) says to support a raised vehicle with floor stands and to raise it only on a hard, level surface. OSHA lists the internal combustion engine as a common source of carbon monoxide exposure, so do not run the engine in a closed garage or other enclosed space. Stop and see a qualified technician for a flashing warning light with other messages, a fuel leak, or a seized or broken plug.

Wiring: describe the circuit, no service diagram

This page does not reproduce a Ford wiring diagram. In plain terms, the circuit is: battery power, through the relay or module, to each glow plug, with the PCM deciding when. Sensors for oil temperature and barometric pressure tell the PCM how long. For the exact wire colors, connector pins and fuse locations on your truck, use the Ford workshop manual.

If you are weighing a repair, read what drives the cost of the job.

Answers to common questions

Where is the relay?

The Ford documents we opened do not say where the 7.3L glow plug relay is mounted, so we will not guess. Location can vary by model year and body style. Use the Ford owner guide or workshop manual for your exact truck, or ask a qualified technician, and have the battery handled as that manual directs before touching any electrical part.

Can a bad relay cause no-start?

It can contribute to a hard cold start, because the relay is part of the circuit that powers the plugs. Ford says the glow plug system should be checked and repaired promptly if the WAIT TO START light does not come on, to avoid cold-starting difficulty. Many other faults produce similar symptoms, so test before replacing parts.

Relay or plugs?

Both are possible and a technician should tell them apart with the maker's procedure. Ford lists the relay and eight plugs together in one system, controlled by the PCM with oil temperature and barometric pressure sensors. Bosch also says a failed controller can overheat and ruin plugs. Replacing parts without testing risks spending money without fixing the cause.

Does the relay and the wait-to-start light work together?

The light is driven by the control system, not by proof that the plugs are heating. Ford says the light illuminates if glow plug heat is necessary, and that the glow plug system operates under PCM control. The documents opened do not state that the light confirms the plugs are drawing current, so a lit light alone does not clear the relay.

Do all 7.3 trucks use a relay?

Not necessarily. Ford's owner supplement lists a glow plug relay, while Ford's diagnostic summary describes a California-calibrated system with a solid-state glow plug control module instead. Emissions package and model year can change what a truck has, so confirm in Ford documentation for your vehicle before buying or testing any part.

Sources

Worth reading next

Back to top